Before you begin to configure iDRAC on the Symantec Advanced Threat Protection: Network (ATP: Network) 8880 appliance, make sure that the appliance is connected to AC power. This gives power to the iDRAC, even if you do not turn on the appliance. When the service tag number appears on the iDRAC display, the iDRAC is ready to be configured. Although you can use DHCP to configure the iDRAC network settings, a best practice is to assign a static IP address. The iDRAC front panel has these three buttons for selecting, changing, and entering data: ✓ = Enter = Move the selection to the right or increase the value (depending on the context) Configuring the iDRAC with a static IP address. To assign a static IP address to the iDRAC • Press ✓ to enter the menu system. • Press > to highlight Setup and then press ✓. • With iDRAC highlighted, press ✓. If the.78 IP is just to be used for DRAC then ensure it is not set in the OS. If you need the.78 for both the OS and the DRAC then you're out of luck, find another spare IP and assign that to the drac with racadm instead of.78. Sep 27, 2017 - Configure Static IP for iDRAC. It should say Press CTRL + E for Remote Access Setup within 5 sec. You'll definitely want to make sure iDRACx LAN is set to ON. At the very top, you should see NIC Selection, which I recommend setting to Dedicated. You'll have to arrow down quite a bit until you get to IPv4 settings. Clickonce deployment and windows installer deployment pay. • Press > to highlight StaticIP and press ✓. The front panel displays a default IP address. You need to change only the numbers that differ from the static IP address you want to assign. • Press > until you have highlighted a number that you want to change, and then press ✓ to select it. • Press > to increase the value or until » is highlighted, and then press ✓. • The display shows the default subnet mask ( Sub). Use the instructions in steps and to modify values as needed. • Press > until » is highlighted, and then press ✓. • The display shows the default gateway IP address ( Gtw). Use the instructions in steps and to modify values as needed. • Press > until » is highlighted, and then press ✓. • The display asks if you want to set up DNS. This is recommended; setting up DNS lets you program network resources on the iDRAC based on DNS names, rather than requiring you to enter IP addresses. To set up DNS, highlight Yes and press ✓. If you do not want to set up DNS, highlight No and press ✓. Then highlight Save and press ✓. Configuration is complete. • The iDRAC displays the default address of the primary DNS server ( D1). Use the instructions in steps and to modify values as needed. • The iDRAC then displays the default address for an alternate DNS server ( D2). An alternate server is optional, but provides redundancy in case the primary DNS server fails. Use the instructions in steps and to modify values as needed. If you do not want to configure an alternate server, set all values to zeros. • When prompted to Save, highlight Yes and press ✓. Lets say for a minute you’re trying to configure your first SAN. Now, lets pretend that first SAN is a Compellent SC8000. Ya know, cause that’s what we all learn on. You may then be aware that setting up the first and second controller, is not the easiest configuration task. Now, lets pretend, you want to set this up at your desk, so you don’t have to sit in the cold datacenter, executing terminal commands via DB9 serial. Has anyone else wanted that?? Maybe it’s just me, and i’m getting old. Whatever the case may be, the purpose of this document, is to show you how to pass the serial connection through the idrac on an Compellent SC8000 controller but this should work on a R720 class Dell PowerEdge server. (The chassis’s are almost identical) This is a little complicated, but rewarding, so you don’t have to sit in the datacenter. ( however – may pose a small security risk, so you decide.) Steps: There are a few settings we need to make in the BIOS for this to work. (Don’t get this confused with the IDRAC settings – you NEED to actually reboot the server and get into the BIOS and make these settings.) 1. Reboot the server, and at the DELL splash screen, hit the F2 button to Enter System Setup.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |